-
DT830D Digital Multimeter
This is most commonly used entry level Digital Multimeter. The DT830D multime...
This is most commonly used entry level Digital Multimeter. The DT830D multimeter can measure AC Voltage, DC Voltage, DC current and resistance. Apart form that it can also be used to check diodes, LEDs and transistor. It also has overload protection and low battery indicator.... -
555 Timer IC (LM555 / NE555 / SE555) - 8 Pin DIP Package
One of the classics and may be the most used IC is LM555. The possibilities a...
One of the classics and may be the most used IC is LM555. The possibilities and number of applications using this chip is phenomenal. LM555 is a precision timer IC, that is capable of producing accurate time delays or oscillation. It can operate in... -
ESP8266 NodeMCU CP2102 WiFi Development Board
NodeMCU ESP8266 is an open-source Lua based firmware and development board sp...
NodeMCU ESP8266 is an open-source Lua based firmware and development board specially targeted for IoT based applications. It includes firmware that runs on the ESP8266 Wi-Fi SoC from Espressif Systems and hardware which is based on the ESP-12 module, and like this, it can also be programmed... -
NodeMCU ESP8266 CH340 Wi-Fi Module
This ESP8266 NodeMCU CH340 WiFi Module with 4MB flash is ideal for IoT, a...
This ESP8266 NodeMCU CH340 WiFi Module with 4MB flash is ideal for IoT, automation, and wireless embedded projects. Features Built-in Wi-Fi SoC based on ESP8266 for seamless IoT connectivity Integrated CH340 USB-to-Serial converter for stable programming Breadboard-friendly NodeMCU design with accessible GPIO pins Supports... -
Desoldering Braid Solder Remover Wick Wire
It is a 2.5mm solder removing wick wire that is 25cm in length. This wick is ...
It is a 2.5mm solder removing wick wire that is 25cm in length. This wick is very useful when you are doing heavy de-soldering work. The wick is made of copper wire coated with rosin flux which helps in absorbing the waste solder lead... -
SPDT 5V PCB Mount Relay - Sugar cube 5 pin
This is the 5V relay most commonly used as switching device in electronic cir...
This is the 5V relay most commonly used as switching device in electronic circuits. It is mainly used in Commonly switching circuits, For Home Automation projects to switch AC loads, To Control (On/Off) Heavy loads at a pre-determined time/condition, Used in safety circuits to... -
SPDT Miniature Slide Switch
This SPDT Miniature Slide Switch is the perfect ON/OFF switch for your electr...
This SPDT Miniature Slide Switch is the perfect ON/OFF switch for your electronics projects. It has 3 Poles and is Single Pole Double Throw (SPDT) which means that when you slide the switch to the up position, the top and middle poles get connected, and... -
ESP32S 38Pin Development Board (WIFI+BLUETOOTH)
The ESP32S is a Wi-Fi Development Board with in-built Bluetooth Low Energy (B...
The ESP32S is a Wi-Fi Development Board with in-built Bluetooth Low Energy (BLE) that is commonly used in IoT applications. The Board is based on the ESP WROOM32 Module from Espressif Systems. The compact Module can work on 3.3V and consumes low power making... -
RGB LED - 5mm - Common Cathode
The 4 leg RGB LED is an ideal component that can be used in projects that req...
The 4 leg RGB LED is an ideal component that can be used in projects that require multicolor displays. A single RGB LED serves the purpose of three individual different colour LEDs. The RGB name stands for Red colour, Blue colour, and Green colour... -
10K ohm, 1/4 Watt Resistor with 5% tolerance (Pack of 10)
This is a set of 10, 10K ohm carbon film resistors with 1/4 Watt and 5% toler...
This is a set of 10, 10K ohm carbon film resistors with 1/4 Watt and 5% tolerance. Each resistor has strong leads and easy-to-read color coding for breadboarding. In addition, the leads are about 0.55 mm in diameter and are constructed of tin and copper plated over steel wire. This... -
OLED Display 0.96 Inch I2C Interface / 4 Pin Blue SSD1306
OLED displays are popular for their low current consumption and bright viewin...
OLED displays are popular for their low current consumption and bright viewing angles. This 0.96 Inch Monochrome (Blue) OLED display can be easily interfaced with microcontrollers like Arduino through I2C/IIC Communication. The 0.96" display is driven by the SSD1306 Display Driver IC. There are... -
2x3 inch Single Side Copper Plate Perf Board for PCB Prototype / Dotted Board / General Purpose PCB / Zero PCB
In developing any Electrical and Electronics System we must first conceptuali...
In developing any Electrical and Electronics System we must first conceptualize and design the circuit and then go to testing and debugging only after these two stages are complete, we go for final fabrication on the PCB. In all these three processes testing and... -
1N4007 Diode (Pack of 5)
The IN4007 diode is a device which allows current flow through only one direc...
The IN4007 diode is a device which allows current flow through only one direction. That is the current should always flow from the Anode to cathode. For 1N4007 Diode, the maximum current carrying capacity is 1A it withstand peaks up to 30A. Hence we can use... -
1.8V - 12V/2A DC Motor PWM Speed Controller
This 1.8V – 12V/2A DC Motor PWM Speed Controller controls the speed of a DC m...
This 1.8V – 12V/2A DC Motor PWM Speed Controller controls the speed of a DC motor with high efficiency, high torque and low heat generation. Features Provides precise speed control using Pulse Width Modulation (PWM) technology. Supports a wide range of DC motor voltages... -
2-Pin SPST ON-OFF Mini Rocker Switch - 2A 250V
This is a basic 2-pin SPST On-Off mini rocker switch with current ratings of...
This is a basic 2-pin SPST On-Off mini rocker switch with current ratings of 2A 250V AC. This Rocker Switch has markings of 0 and 1 to identify the on-off configuration, and is ideal for controlling power to electronic circuits, boards, etc. It is not a momentary switch and so remains... -
1mm Micro Drill Bit HSS Straight Shank Electrical Tool Twist Drilling Bit
Drill bits are important for Handmade PCBs and the most common diameter is th...
Drill bits are important for Handmade PCBs and the most common diameter is the 1mm. Many components such as through hole resistors as well as through hole capacitors use 1mm drill hole size and this is a high-quality PCB drill bit with the required diameter of 1 mm.... -
2 Pin PCB Mount Terminal Block (Screw type) - 5mm Pitch
PCBs are used in almost all the electronic appliances as they are highly effi...
PCBs are used in almost all the electronic appliances as they are highly efficient and make the development and execution of the electronic circuits very easy. You can make one PCB and if tolerances and design is good the PCB will last for years... -
Heat Shrink Sleeve Tube - 3mm Diameter - Black - 1 meter
Heat Shrink Tube is required when you want to build your wiring harness to be...
Heat Shrink Tube is required when you want to build your wiring harness to be resistant to abrasion, scrubbing and provide insulation to stranded and solid wire conductors, joints, connectors and terminals in the electrical systems. It is a plastic tube which shrinks rapidly when exposed to heat which... -
L293D Motor Driver Shield for Arduino
Stepper and DC Motors are essentially used in any of the DIY Robotics project...
Stepper and DC Motors are essentially used in any of the DIY Robotics projects and other applications can be found in 3D printing and steering DIY cars. Most commonly used IC for low power applications for controlling these motors in dual H bridge L293D... -
Type C Female Connector with Wire for DIY
Type C Female Power Cable Panel Mount is used widely for phone accessory, PCB...
Type C Female Power Cable Panel Mount is used widely for phone accessory, PCB Socket. And More electronic projects you can do school and collage projects with the help of Type C cable open type in yellow color. Also can be used for products where the... -
Soil Moisture Sensor Module
The soil moisture sensor is commonly used in smart agriculture or other garde...
The soil moisture sensor is commonly used in smart agriculture or other garden automation projects to measure the moisture content present in the soil. It consists of 4 pins in which two pins, Vcc and Gnd are connected to supply voltage. The remaining two... -
16x2 LCD Display (Green Backlight)
The 16x2 Alphanumeric LCD Display Module is equally popular among hobbyists ...
The 16x2 Alphanumeric LCD Display Module is equally popular among hobbyists and professionals for its affordable price and easy to use nature. As the name suggests the 16x2 Alphanumeric LCD can show 16 Columns and 2 Rows therefore a total of (16x2) 32 characters... -
Heat Shrink Sleeve Tube - 2 mm Diameter - Black - 1 meter
Heat Shrink Tube is required when you want to build your wiring harness to be...
Heat Shrink Tube is required when you want to build your wiring harness to be resistant to abrasion, scrubbing and provide insulation to stranded and solid wire conductors, joints, connectors and terminals in the electrical systems. It is a plastic tube which shrinks rapidly when exposed to heat which... -
3V Miniature DC Motor
This is a simple miniature brushed 3V DC motor that is commonly used in hobby...
This is a simple miniature brushed 3V DC motor that is commonly used in hobby projects. The motor has an operating voltage between 3V to 6V and a no-load current of 350mA when operating at 3V. The axial length is 9mm and the Shaft... -
3S 40A Li-ion Battery Protection BMS Board for 3.7V NMC cells
This 3S 40A Li-ion Battery Protection Board BMS is designed to protect lithiu...
This 3S 40A Li-ion Battery Protection Board BMS is designed to protect lithium-ion batteries that have a normal voltage of 3.7V and a fully charged voltage of 4.2V. The Li-ion Battery Protection Board is basically a protection IC for 3-serial-cell lithium-ion/ lithium polymer rechargeable... -
I2C Serial Interface LCD Adapter Module
Commercially available LCD display modules like 16x2 LCD display and 20x4 LCD...
Commercially available LCD display modules like 16x2 LCD display and 20x4 LCD display are great to be used with a microcontroller like Arduino, Raspberry Pi, PIC, etc. to display the data but a standard 16x2 LCD even when operating at 4-bit mode takes about 8... -
LDR Sensor Module - Photosensitive Light Detection Sensor Module
Ambient light sensing is a significant part of many applications like automat...
Ambient light sensing is a significant part of many applications like automatic street lights, solar panels charging controller, automatic irrigations systems where humidity and ambient light determine if the planet needs to be irrigated or not. We usually use a simple Light Dependent Resistor... -
XL4016 Step Down Buck Converter (300W 10A Power Supply Module)
Buck converter is used when you require to step down the DC voltage from a sp...
Buck converter is used when you require to step down the DC voltage from a specified value to a lower value in DC voltage. Unlike AC voltage which you can control easily with a transformer, DC voltages are harder to control because you can’t... -
4 Cell 18650 Lithium Battery Holder
This 18650 Lithium Battery Holder is a high-quality Lithium battery holder th...
This 18650 Lithium Battery Holder is a high-quality Lithium battery holder that can hold four 18650 Lithium batteries. It's a space-saving battery holder with built-in PCB protective circuits for securing rechargeable 18650 Lithium-Ion Cells with increased energy density and reduced weight. This Lithium Battery... -
Dual Axis XY Joystick Module
This is a Dual Axis Joystick Module to measure position coordinates on the X ...
This is a Dual Axis Joystick Module to measure position coordinates on the X and Y axis by moving the “hat”. Directional movements are controlled by simply two potentiometers of 10k ohm – one for each axis. This PS2 Joystick module sensor also has a... -
0.8mm Micro Drill Bit HSS Straight Shank PCB
Drill bits are important for Handmade PCBs and the most common diameter is th...
Drill bits are important for Handmade PCBs and the most common diameter is the 0.8mm. Many components such as through hole resistors as well as through hole capacitors use 0.8mm drill hole size and this is a high-quality PCB drill bit with the required... -
Nano R3 CH340 Chip Development Board - Compatible with Arduino - Soldered (Without Cable)
Nano is a small, breadboard-friendly development board based on an ATmega 328...
Nano is a small, breadboard-friendly development board based on an ATmega 328P/ATMEGA168 SMD package microcontroller and offers the same connectivity and specs of Uno in a small package. DC Power Jack is not available on this board so power can only be supplied by a Mini B USB port...
Best Selling Products
Close
Sidebar
Categories
- Development Boards
-
Sensor Modules
- Color Sensors
- Current Sensors
- Distance Sensors
- Fingerprint Sensors
- Flex Sensors
- Flow Sensors
- Gas Sensors
- Hall/Magnet Sensors
- Heartbeat Sensors
- Humidity Sensors
- Temperature/Humidity Sensors
- IR/Motion Sensors
- Light Sensors
- Motion/Tilt Sensors
- PH Sensors
- Pressure Sensors
- Accelerometer and Gyrometer Sensors
- Proximity Sensors
- Rain/Soil Moisture Sensors
- Soil Sensors
- Sound Sensor
- Touch Sensors
- Vibration Sensors
- Voltage Sensors
- Water Level/Flow Sensors
- Weighing Sensors
- RFID Tags and Modules
- Semiconductors & Prototyping Components
- Batteries, Power Supplies & Accessories
- Wireless & IoT Products
- Switches, Relays & Protection
- Lighting & LEDs
- Motors, Drivers & Pumps
- Wires, Cables & Connectors
- Robotics & DIY Learning Kits
- 3D Printers & Parts
- SMD Components
- Electronic Modules
- Drone Components
- Hardware Instruments & Tools
- Displays
- Shop By Brand
- Choosing a selection results in a full page refresh.