PICkit3 PIC Programmer with Universal Adapter PICkit3 PIC Programmer with Universal Adapter

QC0019

10 In stock

Rs. 1,709.00
-
+
Rs. 1,709.00
(inc. GST)

The PICKit 3 programmer/debugger is a simple, low-cost in-circuit debugger that is controlled by a PC running MPLAB X IDE running on the Windows platform. It can program or debug and perform Hardware and Software development of the PIC microcontrollers and dsPIC Digital Signal Controllers (DSPs) that are based on In-Circuit Serial Programming (ICSP). It programs the ICs using only two wires PGD and PGC apart from power pins. The debugger system executes code like an actual device because it uses a device with built-in emulation circuitry, instead of a special debugger chip, for emulation. All available features of a given device are accessible interactively and can be set and modified by the MPLAB IDE interface.

 

Specifications

  • Voltage 2V to 6V
  • Used to program and debug PIC microcontrollers
  • Easy to interface with PC via USB cable
  • Has programmer to go feature where you can program without PC with 512KB of Flash memory
  • Built-in Over Voltage and Short circuit Monitor
  • On-board diagnostic LED’s for Power, Busy and Error
  • Supports all latest version of PIC and IDE’s

 

Product Description

 

To connect the PICKit 3 to your microcontroller if it supports ICSP, then look into their pinouts for Vpp, Vss, Vdd, ICSPDAT, and ICSPCLK pins. The pin number will vary from package to package. Once you find the pins, simply connect them to PicKit using jumper wires and program your controller using MPLAB X IDE from your PC. Always make sure that both the Controller and PicKit are power during this operation with an appropriate voltage.

Difference between Pickit 2 and PicKit 3

Pickit 2 is the predecessor of PicKit 3. Both do almost the same job, but Pickit 3 has some additional options and supports for the latest versions of PIC. Also, debugging will be a bit faster than Pickit 2. If you are a beginner, then even Pickit 2 would work fine. If you are looking for more advanced options like Logic analyzer built-in, then have a look at ICD3. 

 

Package Contents

1 x Pickit3 Module

1 x Universal programmer adapter

1 x Connecting Wire

 

Additional Resources

Datasheet for PICKit 3

Getting Started with PICKit 3

The PICKit 3 programmer/debugger is a simple, low-cost in-circuit debugger that is controlled by a PC running MPLAB X IDE running on the Windows platform. It can program or debug and perform Hardware and Software development of the PIC microcontrollers and dsPIC Digital Signal Controllers (DSPs) that are based on In-Circuit Serial Programming (ICSP). It programs the ICs using only two wires PGD and PGC apart from power pins. The debugger system executes code like an actual device because it uses a device with built-in emulation circuitry, instead of a special debugger chip, for emulation. All available features of a given device are accessible interactively and can be set and modified by the MPLAB IDE interface.

 

Specifications

  • Voltage 2V to 6V
  • Used to program and debug PIC microcontrollers
  • Easy to interface with PC via USB cable
  • Has programmer to go feature where you can program without PC with 512KB of Flash memory
  • Built-in Over Voltage and Short circuit Monitor
  • On-board diagnostic LED’s for Power, Busy and Error
  • Supports all latest version of PIC and IDE’s

 

Product Description

 

To connect the PICKit 3 to your microcontroller if it supports ICSP, then look into their pinouts for Vpp, Vss, Vdd, ICSPDAT, and ICSPCLK pins. The pin number will vary from package to package. Once you find the pins, simply connect them to PicKit using jumper wires and program your controller using MPLAB X IDE from your PC. Always make sure that both the Controller and PicKit are power during this operation with an appropriate voltage.

Difference between Pickit 2 and PicKit 3

Pickit 2 is the predecessor of PicKit 3. Both do almost the same job, but Pickit 3 has some additional options and supports for the latest versions of PIC. Also, debugging will be a bit faster than Pickit 2. If you are a beginner, then even Pickit 2 would work fine. If you are looking for more advanced options like Logic analyzer built-in, then have a look at ICD3. 

 

Package Contents

1 x Pickit3 Module

1 x Universal programmer adapter

1 x Connecting Wire

 

Additional Resources

Datasheet for PICKit 3

Getting Started with PICKit 3

Returns Policy

Due to the type of products we sell, we accept limited returns. Below are the conditions where we can accept a return request.

1. Manufacturing Defect
If you receive a product with a manufacturing defect, please notify us within the 3 days of you receive the product, supported by the proper pictures and description. Once our support team accept the return, we will provide a replacement or a complete refund including the return shipping cost.

2. Wrong Item Shipped

If you receive a different product then the ordered one, please contact us within the 3 days of you receive the product, supported by the proper pictures and description. Once our support team accept the return, we will provide a replacement or a complete refund including the return shipping cost.

Limitation of Returns
We don't accept the returns for the products damanged by improper use of the product. Moreover we don't accept the return, if the ordered product is not fit for any specific application. Please read the product specifications and datasheet before selecting and ordering a product.

Shipping

We ship to all over India with flat shipping rate of INR 45 for all the orders below INR 499. For all the orders above INR 499, we offer a free shipping. Please contact to our support team at support@quartzcomponents.com for any question related to shipping.

Returns Policy

Due to the type of products we sell, we accept limited returns. Below are the conditions where we can accept a return request.

1. Manufacturing Defect
If you receive a product with a manufacturing defect, please notify us within the 3 days of you receive the product, supported by the proper pictures and description. Once our support team accept the return, we will provide a replacement or a complete refund including the return shipping cost.

2. Wrong Item Shipped

If you receive a different product then the ordered one, please contact us within the 3 days of you receive the product, supported by the proper pictures and description. Once our support team accept the return, we will provide a replacement or a complete refund including the return shipping cost.

Limitation of Returns
We don't accept the returns for the products damanged by improper use of the product. Moreover we don't accept the return, if the ordered product is not fit for any specific application. Please read the product specifications and datasheet before selecting and ordering a product.

Shipping

We ship to all over India with flat shipping rate of INR 45 for all the orders below INR 499. For all the orders above INR 499, we offer a free shipping. Please contact to our support team at support@quartzcomponents.com for any question related to shipping.

Recently Viewed Products Recently Viewed Products