Sale
L298N 2A Based Motor Driver Module
L298N 2A Based Motor Driver Module
L298N 2A Based Motor Driver Module
Click to zoom in
  • Free Shipping

    On prepaid orders above INR 500

  • Cash On Delivery

    COD available for orders above INR 500

  • 3-5 Days Delivery

    Shipped within 24 hrs

  • Dedicated Support

    Mon to Sat - 10 AM to 6.30 PM

L298N 2A Based Motor Driver Module

QC0402
301 In stock
Rs. 109.00 Rs. 98.00 (Exc. GST)
Rs. 98.00

A microcontroller that normally operates on 5V or 3.3V cannot be directly used to control a DC motor operating on higher voltage and current rating. This is why we commonly use Motor Driver modules like the L293D Motor Driver Module and the L298N Motor Driver Module. While the L293D motor driver module can be used for basic low current application the L298N Motor driver module is a high current motor driver with some additional features that are commonly used with Arduino and Raspberry Pi for Robotics applications.

The L298N Motor Driver module is based on the L298 Dual Full-Bridge Driver IC and can control the speed and direction of two DC motors (Motor A and Motor B) simultaneously. The voltage rating of these motors can be between 5V to 35V and the peak current value can be up to 2A. The pinout diagram of the L298N Motor Driver Module is shown below.

The motors to be controlled (Motor A and B) are connected to screw terminals. The voltage required to power the motor is provided to the Motor Power and Ground screw terminal, the voltage range should be between 7V to 35V. The L298 IC requires 5V to operate, this is why we have a built-in 5V Linear Regulator. If the operating voltage of the motor is less than or equal to 12V than the built-in regulator will power the driver IC, and this regulated 5V can also be obtained as an output voltage from the 5V screw terminal which can be used to power your microcontrollers like Arduino. If the operating voltage of the motor is greater than 12V then the built-in regulator will not be able to handle it, so we have to disconnect the regulator by removing the 5V Select Jumper pin and provide a separate 5V power as an input voltage to the 5V screw terminal to power our L298N Driver IC.

The pins Enable A and Enable B are used to set the speed of the motor. By default, there will be jumper pins connected to both Enable A and B to make them high (5V), this way the motors will rotate at maximum speed. You can adjust the speed of the motors by removing the jumper and providing a variable voltage between 0V to 5V by using a PWM signal.

Finally, the four input pins Input 1, 2, 3, and 4 are used to control the direction of the motor. For example, if Input 1 and Input 2 are made High and Low, respectively, then Motor A will rotate in clockwise. If they are made Low and High, then the motor will rotate counterclockwise. The same logic applied for Input 3 and 4 with Motor B.

Specifications of L298N Motor Driver IC:

  • Input Voltage: 3.2V to 40Vdc
  • Driver: L298N Dual H Bridge DC Motor Driver
  • Operating voltage: DC 5V – 35V
  • Peak Current: 2 Amps
  • Speed Control: PWM
  • Control Signal input Low voltage range: 0.3V ≤ Vin ≤ 1.5V
  • Control Signal input High voltage range: 2.3 ≤ Vin ≤ Vss
  • Enable signal input low voltage range: 0.3V ≤ Vin ≤ 1.5V (enable signal inactive)
  • Enable signal input high voltage range: 2.3V ≤ Vin ≤ Vss (enable signal active)
  • Maximum power consumption: 20W (when the temperature T = 75℃)
  • Onboard +5V regulated Output supply

    The basic dimensions of the L298N Motor Driver module are shown below.

                                             

    Additional Resources:

    Read More
    Read Less

    Returns Policy

    Due to the type of products we sell, we accept limited returns. Below are the conditions where we can accept a return request.

    1. Damaged During Shipment
    If you receive a product damaged during shipment, please notify us within the 3 days of you receive the product, supported by the proper pictures and description. Once our support team accept the return, we will provide a replacement or a complete refund including the return shipping cost.

    2. Wrong Item Shipped

    If your item looks different from what is shown in the image on our website, we will take the item back and provide a refund or replacement as per your choice.

    Limitation of Returns
    We don't accept the returns for the products damanged by improper use of the product. Moreover we don't accept the return, if the ordered product is not fit for any specific application. Please read the product specifications and datasheet before selecting and ordering a product. Returns are accepted only with 3 days from the date of delivery.

    Shipping

    We ship to all over India with free shipping on all prepaid orders above 500. For Cash on Delivery orders INR 80 will be charged for orders below INR 599 and INR 30 will be charged for the orders above 599. Please contact to our support team at support@quartzcomponents.com for any question related to shipping.


    Please note that the Minimum Order Value is INR 500 for COD orders.

    Customer Reviews

    Based on 26 reviews
    85%
    (22)
    0%
    (0)
    4%
    (1)
    4%
    (1)
    8%
    (2)
    D
    DHRUV Singh
    Defected pieces

    That's a worth product

    Z
    Zafeer Mandli

    It was not working

    D
    Deev Mehta

    L298N 2A Based Motor Driver Module

    H
    Hukum Singh

    it is working well

    S
    Subhrajit Nandi

    L298N 2A Based Motor Driver Module

    Customer Reviews

    Based on 26 reviews
    85%
    (22)
    0%
    (0)
    4%
    (1)
    4%
    (1)
    8%
    (2)
    D
    DHRUV Singh
    Defected pieces

    That's a worth product

    Z
    Zafeer Mandli

    It was not working

    D
    Deev Mehta

    L298N 2A Based Motor Driver Module

    H
    Hukum Singh

    it is working well

    S
    Subhrajit Nandi

    L298N 2A Based Motor Driver Module

    Your cart

    ×